March 809 High Temperature Brewing Pump included 1/2" nickel plated ball valve and fittings as shown to mate to 1/2" tubing
The March 809 Polysulphone sealess magnetic head pump is new and it is the best value and our best pump. It is designed for hot liquids and rated at 250? F. The pump is capable of 5 gallons per minute up to 12 feet of head. This pump dissembles for cleaning by removing the four screws on the front of the housing. To connect, push your half-inch ID tubing onto the included barb fittings. an electric plug and six feet of cord is included. All threaded fittings are a big half-inch to prevent clogging. Everything shown is included. Use the included 1/2" nickel plated ball valve to restrict flow when running a recirculating mash system.
We found the ideal brewing pump built by March Manufacturing. The main factors we were looking for was a pump that was constructed of food-grade material, would handle wort at boiling temperature, take back pressure (flow restriction). We chose to have the pump housing made from polysulfone because it is a tough, food-grade plastic rated to temperatures as hot as 250F. It offers many of the benefits of the ideal material, stainless steel, without the prohibitive cost.
The magnetic drive acts as a clutch allowing the user to put back pressure on the pump to slow down flow. Since it is magnetic drive, it is not self-priming, you must put the pump under the level of the liquid source.
This is a tough little pump with a 1/25 hp, continuous-duty 1.4 Amp motor which can be run non-stop for extended periods.
1/2" mpt fittings on both inlet and outlet. Materials in contact with solution are Polysulfone, 316 stainless steel, silicon rubber, Raton and Teflon. Shaded pole, thermal overload protected, single phase motor is fan cooled. Will handle internal pressures to 150 psi. Max pressure the pump can produce in a closed system is a little over 5 psi. Face unscrews and rotates at 90 degree intervals to adjust to your application.
All threaded fittings are a big half-inch to prevent clogging. Everything shown is included. Use the included 1/2" lead free ball valve to restrict flow when running a recirculating mash system.
Quick Disconnect Hose Connector - Female
With these quick disconnect, life is easier and safer. No buttons to press, just turn and pull or push and turn. All fittings are 1/2" barb or thread.
They do not have any shutoff feature, so no fluid should be in your lines when breaking connections
Able to withstand boiling temperatures
They are made from nylon and melt at 250 degrees
so avoid direct flame exposure.
Recomended on equipment side of connection
Mates With item HBQCM
Quick Disconnect Hose Connector - Male
With these quick disconnect, life is easier and safer. No buttons to press, just turn and pull or push and turn. All fittings are 1/2" barb or thread.
They do not have any shutoff feature, so no fluid should be in your lines when breaking connections
Able to withstand boiling temperatures
They are made from nylon and melt at 250 degrees
so avoid direct flame exposure.
Recomended on hose side of connection
Mates With item HBQCF
March 809 High Temperature Brewing Pump included 1/2" nickel plated ball valve and fittings as shown to mate to 1/2" tubing
The March 809 Polysulphone sealess magnetic head pump is new and it is the best value and our best pump. It is designed for hot liquids and rated at 250? F. The pump is capable of 5 gallons per minute up to 12 feet of head. This pump dissembles for cleaning by removing the four screws on the front of the housing. To connect, push your half-inch ID tubing onto the included barb fittings. an electric plug and six feet of cord is included. All threaded fittings are a big half-inch to prevent clogging. Everything shown is included. Use the included 1/2" nickel plated ball valve to restrict flow when running a recirculating mash system.
We found the ideal brewing pump built by March Manufacturing. The main factors we were looking for was a pump that was constructed of food-grade material, would handle wort at boiling temperature, take back pressure (flow restriction). We chose to have the pump housing made from polysulfone because it is a tough, food-grade plastic rated to temperatures as hot as 250F. It offers many of the benefits of the ideal material, stainless steel, without the prohibitive cost.
The magnetic drive acts as a clutch allowing the user to put back pressure on the pump to slow down flow. Since it is magnetic drive, it is not self-priming, you must put the pump under the level of the liquid source.
This is a tough little pump with a 1/25 hp, continuous-duty 1.4 Amp motor which can be run non-stop for extended periods.
1/2" mpt fittings on both inlet and outlet. Materials in contact with solution are Polysulfone, 316 stainless steel, silicon rubber, Raton and Teflon. Shaded pole, thermal overload protected, single phase motor is fan cooled. Will handle internal pressures to 150 psi. Max pressure the pump can produce in a closed system is a little over 5 psi. Face unscrews and rotates at 90 degree intervals to adjust to your application.
All threaded fittings are a big half-inch to prevent clogging. Everything shown is included. Use the included 1/2" lead free ball valve to restrict flow when running a recirculating mash system.
HomeBrew4Less.com LLC, 890 Lincoln Way
W, Chambersburg, PA 17202
(717) 504-8534
Store Hours Tue to Sat 11:30 am to 5:30 pm
Telephone Support 8 am to 8 pm
*** We only ship within the United States. ***
The American Homebrewers Association (AHA) is committed to promoting the community of homebrewers and empowering homebrewers to make the best beers in the world. Join today!
